BUILDING AUTOMATION TRAINING SYSTEM
A
1 A versatile, robust and easy to use training system suitable for teaching, learning and implementing KNX based electrical component/modules wiring, installation, monitoring, programming and maintenance. 2. The system is designed in a panel platform with metal case and clearly labelled front panel. KNX modules are fitted with 4mm and 2mm safety sockets. Allows connecting using 4mm and 2mm connecting leads. 3. Bundled with extensive guided laboratory lab workbook to enhance the teaching and learning experience.
DESCRIPTIONS :
DONWLOAD DONWLOAD
MODEL: KNX-TRAINER KIT-TK04A
TECHNICAL SPECIFICATION
ABLELOGIC.COM.MY
a) PROTECTION & DISTRIBUTION MODULE (1 unit) • 1 no. of 20A RCCB, 30mA sensitivity • 1 no. of 32A MCB and 5 no. of 20A MCB • Complete with neutral bar and cabling termination • Metal Casing with Panel Dimension 210mm(L) X 338mm(H) and rubber b) POWER SUPPLY MODULE (2 units) • Power : 230V, 50/60Hz • Outputting voltage: 28 - 31VDC • Output current: 640mA • Additional Output: 30V DC auxiliary voltage • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber c) SWITCH ACTUATOR MODULE, 4 CH (1 unit) • Operating voltage over bus: 21-32Vdc • Auxiliary voltage: 230V • Resistive Load: 16A/230VAC AC1, 16A/24VDC • Manual operation button: 4 nos. of mechanical bypass • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber d) DIMMING ACTUATOR MODULE, 2 CH (1 unit) • Operating voltage over bus: 21-32V • Control voltage: 230V • Electronic transformer: 400W per channel • Output Channel: 2 nos. • Comply with KNX protocol • Metal Casing with Panel Dimension 250mm(L) X 338mm(H) and rubber e) SHUTTER ACTUATOR MODULE (1 unit) • Operating voltage over bus: 21-32Vdc • Auxiliary voltage: 230V • Capacity load: 6A • Manual operation button : 4 nos. of bypass button • Comply with KNX protocol • Metal Casing with Panel Dimension 210mm(L) X 338mm(H) and rubber f) DALI GATEWAY MODULE (1 unit) • Operating voltage over bus: 21-32Vdc • Auxiliary voltage: 230V • Can support up to 64 device and 14 group control • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber g) PUSH BUTTON MODULE, 1 GANG (1 unit) • Operating voltage: 21-32V • Operation : Programmable button 1/2 • According to the EMC and low voltage guideline, EN 50090-2-2 • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber h) PUSH BUTTON MODULE, 2 GANG (1 unit) • Operating voltage: 21-32V • Operation : Programmable button 2/4 • According to the EMC and low voltage guideline, EN 50090-2-2 • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber i) PUSH BUTTON MODULE, 3 GANG (1 unit) • Operating voltage: 21-32V • Operation : Programmable button 3/6 • According to the EMC and low voltage guideline, EN 50090-2-2 • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber j) USB INTERFACE MODULE (1 unit) • Operating voltage over bus: 5Vdc • USB Interface : Stick Type , Type A • Programming Cable: 1m (min.) • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber k) LIGHT with DALI BALLAST MODULE (1 unit) • Total of 28W with DALI 28W ballast of T5 • Consists of 1 DALI Ballast and Light Tubes • Comply with KNX protocol l) LINE COUPLER MODULE (1 unit) • Operating voltage: 21-32V • Operating temperature: - 5 ~ 45 ˚C • Operation : Access Control for Main Line and Sub Line or vice versa. • According to the EMC and low voltage guideline, EN 50090-2-2 • Comply with KNX Protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber m) MOTORISED VENETIAN BLIND (1 unit) • Type : Roller Blind 50mm • Size : Min Width 60cm, Drop 60cm Approximate • Motor : 4 wired AC • Work with KNX protocol Device n) UNIVERSAL INTERFACE MODULE (1 unit) • Operating voltage: 21 – 32V • Input/Output: 4 Channels, can be individual parameterized • Comply with KNX Protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber o) PILOT LAMP MODULE (1 unit) • 4 nos. of pilot lamps (2x RED, 2 x GREEN) • Operating voltage: 240VAC • Work with KNX protocol Device • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber p) HALOGEN LAMP MODULE (1 unit) • 2 nos. of Halogen Lamp • Operating voltage: 240VAC • Work with KNX protocol Device • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber q) 3 GANG CONVENTIONAL SWITCH MODULE (1 unit) • Voltage rating: 240VAC • Current rating: 10A • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber 2. KNX Cable (1 roll) • 1 Roll of 100 Meter KNX Cable • Comply with KNX protocol 3. MOUNTING FRAME (1 unit) • Aluminium/Metal Frame • Side - T Frame • 3 Layer • Dimension : approx. 1050mm (L) 4. ETS SOFTWARE (1 set) • ETS Lite with dongle key for programming software license for devices programming (project for education) • ETS5 LITE VER 5.54 or above/latest • Comply with KNX Protocol 5. TERMINAL CONTROLLER (1 set) • Compatible with ETS LITE 5 programming software iii. Control station: • Required for development, programming & data viewing • Windows 10 Operating System • Preloaded with microcontroller IDE • CPU - i3 or better • 15“ LCD Colour Monitor display or better • Data Storage: 256GB M.2 PCIe NVMe Solid State Drive • RAM: 4GB • USB ports (min. 3) vi. Table Bench • Dimension: Approx. 1500mm(L) x 900mm(W) x 750mm(H) • Benchtop built from high density 25mm thickness highly compressed multilayer/multigrain solid chipboard • Benchtop protection: Scratch- resistant & non abrasive melamine resin Laminate on board, conceal 2mm ABS impact resistance protection for edges • Bench Frame of approx. 38mm x 38mm hollow mild steel coated with epoxy powder coated finishing • 4 steel leg sections attached to 1 common foot sec��on • All 4 frame legs supported by plastic height adjustable legs caps • Color: Light Gray v. Manuals and Accessories: • 4mm connecting Leads (1 set) • Programming Cable x 1 set • User/Operating Manual x1 • Lab Experiment Manual with Answer x1
BUILDING AUTOMATION TRAINING SYSTEM
DONWLOAD DONWLOAD
MODEL: KNX-TRAINER KIT-TK04A
PRODUCT MENU PRODUCT MENU
DESCRIPTIONS :
1 A versatile, robust and easy to use training system suitable for teaching, learning and implementing KNX based electrical component/modules wiring, installation, monitoring, programming and maintenance. 2. The system is designed in a panel platform with metal case and clearly labelled front panel. KNX modules are fitted with 4mm and 2mm safety sockets. Allows connecting using 4mm and 2mm connecting leads. 3. Bundled with extensive guided laboratory lab workbook to enhance the teaching and learning experience.
TECHNICAL SPECIFICATION
a) PROTECTION & DISTRIBUTION MODULE (1 unit) • 1 no. of 20A RCCB, 30mA sensitivity • 1 no. of 32A MCB and 5 no. of 20A MCB • Complete with neutral bar and cabling termination • Metal Casing with Panel Dimension 210mm(L) X 338mm(H) and rubber b) POWER SUPPLY MODULE (2 units) • Power : 230V, 50/60Hz • Outputting voltage: 28 - 31VDC • Output current: 640mA • Additional Output: 30V DC auxiliary voltage • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber c) SWITCH ACTUATOR MODULE, 4 CH (1 unit) • Operating voltage over bus: 21-32Vdc • Auxiliary voltage: 230V • Resistive Load: 16A/230VAC AC1, 16A/24VDC • Manual operation button: 4 nos. of mechanical bypass • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber d) DIMMING ACTUATOR MODULE, 2 CH (1 unit) • Operating voltage over bus: 21-32V • Control voltage: 230V • Electronic transformer: 400W per channel • Output Channel: 2 nos. • Comply with KNX protocol • Metal Casing with Panel Dimension 250mm(L) X 338mm(H) and rubber e) SHUTTER ACTUATOR MODULE (1 unit) • Operating voltage over bus: 21-32Vdc • Auxiliary voltage: 230V • Capacity load: 6A • Manual operation button : 4 nos. of bypass button • Comply with KNX protocol • Metal Casing with Panel Dimension 210mm(L) X 338mm(H) and rubber f) DALI GATEWAY MODULE (1 unit) • Operating voltage over bus: 21-32Vdc • Auxiliary voltage: 230V • Can support up to 64 device and 14 group control • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber g) PUSH BUTTON MODULE, 1 GANG (1 unit) • Operating voltage: 21-32V • Operation : Programmable button 1/2 • According to the EMC and low voltage guideline, EN 50090-2-2 • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber h) PUSH BUTTON MODULE, 2 GANG (1 unit) • Operating voltage: 21-32V • Operation : Programmable button 2/4 • According to the EMC and low voltage guideline, EN 50090-2-2 • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber i) PUSH BUTTON MODULE, 3 GANG (1 unit) • Operating voltage: 21-32V • Operation : Programmable button 3/6 • According to the EMC and low voltage guideline, EN 50090-2-2 • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber j) USB INTERFACE MODULE (1 unit) • Operating voltage over bus: 5Vdc • USB Interface : Stick Type , Type A • Programming Cable: 1m (min.) • Comply with KNX protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber k) LIGHT with DALI BALLAST MODULE (1 unit) • Total of 28W with DALI 28W ballast of T5 • Consists of 1 DALI Ballast and Light Tubes • Comply with KNX protocol l) LINE COUPLER MODULE (1 unit) • Operating voltage: 21-32V • Operating temperature: - 5 ~ 45 ˚C • Operation : Access Control for Main Line and Sub Line or vice versa. • According to the EMC and low voltage guideline, EN 50090-2-2 • Comply with KNX Protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber m) MOTORISED VENETIAN BLIND (1 unit) • Type : Roller Blind 50mm • Size : Min Width 60cm, Drop 60cm Approximate • Motor : 4 wired AC • Work with KNX protocol Device n) UNIVERSAL INTERFACE MODULE (1 unit) • Operating voltage: 21 – 32V • Input/Output: 4 Channels, can be individual parameterized • Comply with KNX Protocol • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber o) PILOT LAMP MODULE (1 unit) • 4 nos. of pilot lamps (2x RED, 2 x GREEN) • Operating voltage: 240VAC • Work with KNX protocol Device • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber p) HALOGEN LAMP MODULE (1 unit) • 2 nos. of Halogen Lamp • Operating voltage: 240VAC • Work with KNX protocol Device • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber q) 3 GANG CONVENTIONAL SWITCH MODULE (1 unit) • Voltage rating: 240VAC • Current rating: 10A • Metal Casing with Panel Dimension 140mm(L) X 338mm(H) and rubber 2. KNX Cable (1 roll) • 1 Roll of 100 Meter KNX Cable • Comply with KNX protocol 3. MOUNTING FRAME (1 unit) • Aluminium/Metal Frame • Side - T Frame • 3 Layer • Dimension : approx. 1050mm (L) 4. ETS SOFTWARE (1 set) • ETS Lite with dongle key for programming software license for devices programming (project for education) • ETS5 LITE VER 5.54 or above/latest • Comply with KNX Protocol 5. TERMINAL CONTROLLER (1 set) • Compatible with ETS LITE 5 programming software iii. Control station: • Required for development, programming & data viewing • Windows 10 Operating System • Preloaded with microcontroller IDE • CPU - i3 or better • 15“ LCD Colour Monitor display or better • Data Storage: 256GB M.2 PCIe NVMe Solid State Drive • RAM: 4GB • USB ports (min. 3) vi. Table Bench • Dimension: Approx. 1500mm(L) x 900mm(W) x 750mm(H) • Benchtop built from high density 25mm thickness highly compressed multilayer/multigrain solid chipboard • Benchtop protection: Scratch- resistant & non abrasive melamine resin Laminate on board, conceal 2mm ABS impact resistance protection for edges • Bench Frame of approx. 38mm x 38mm hollow mild steel coated with epoxy powder coated finishing • 4 steel leg sections attached to 1 common foot sec��on • All 4 frame legs supported by plastic height adjustable legs caps • Color: Light Gray v. Manuals and Accessories: • 4mm connecting Leads (1 set) • Programming Cable x 1 set • User/Operating Manual x1 • Lab Experiment Manual with Answer x1